FIBARO Dimmer 2 can switch or dim connected light source either through radio waves or through the wall switch connected directly to it. New FIBARO Dimmer 2 is equipped with an algorithm of smart light source detection which makes configuration easier and ensures high compatibility of the device.
How to install a Fibaro dimmer?
Installation of the FIBARO Dimmer 2:
- Switch off the mains voltage (disable the fuse)
- Open the wall switch box.
- Connect with one of the diagrams below.
- After verifying correctness of connection switch on the mains voltage.
- Wait around 30s for the calibration process to end, light may blink during the process.
How do you calibrate a Fibaro dimmer 2?
Calibration may be forced:
by setting parameter 13 to 1 or 2 (without/with FIBARO Bypass 2) through triple clicking and holding the main light switch (each hold for more than 5 seconds)
How do I reset my Fibaro dimmer?
Dimmer 2 – “Reset”
- Disconnect the power supply.
- Remove the Dimmer 2 from the wall switch box.
- Connect the power supply.
- Locate the B-button on the housing.
- Press and hold the B-button to enter the menu mode.
- Wait for the visual LED indicator to turn yellow.
- Quickly release and click the B-button again.
How does FIBARO Dimmer work? – Related Questions
Does FIBARO work without Internet?
It can operate independently of other networks, and using OpenHAB, it can work fully locally and off-grid without any need for external Internet nor cloud access.
Does FIBARO need a hub?
FIBARO system works without Internet connection
Calculations and operations of the system are performed locally via the smart home HUB.
How do I reset my Z-Wave dimmer?
3 To return to factory defaults Quickly press the ON button 3 times, then press the OFF button 3 times.
How do you reset a Z-Wave dimmer switch?
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable. 1. Quickly press ON (up) 3 times then immediately press the OFF (Down) button 3 times.
How do I reset my dimmer switch?
Resetting The Dimmer
By pressing the dimmer knob, turn the lights Off and then back On again three times. Leave a second between each dimmer knob press. The lights controlled by the dimmer will step up and then down in brightness to show that the dimmer is in configuration mode.
How do you reset a dimmer Smart switch?
What happens if you wire a dimmer switch wrong?
You’ll need a screwdriver, wire stripper, inexpensive (2 lead wire type) voltage tester and needle-nose pliers to install a dimmer. Wiring problems and mistakes are all too common, and if left uncorrected have the potential to cause short circuits, shocks and even fires.
Why is dimmer switch not working?
#1 Wrong Bulb
This is probably one of the most common problems your average homeowner faces with dimmer switches. It usually happens when the bulb breaks for the first time—as they all do eventually—for that particular homeowner, and they replace the bulb, not knowing that not all bulbs are dimmable.
Why does my dimmer switch not dim the lights?
The most common cause of dimmer powering lights but not dimming is an incompatible bulb. An overloaded or faulty dimmer can also cause it, but also it may be a problem with the wiring.
What happens if you use the wrong dimmer with LED lights?
So, what happens if you use non-dimmable LEDs on a dimmer? Well, at best the bulb just won’t dim properly. At worst, though, you might damage the bulb. You see, dimmable LEDs have special circuitry inside that allows them to respond to varying current levels or “pulsing” current waves to produce a dimming effect.
Do I need a special dimmer for LED lights?
Use an LED Dimmer switch
A standard dimmer switch cannot be used with an LED light as you will never be able to dim the LED light either completely or not very well. LED lights need their own special electronic dimmer switch to have a fully functioning and dimming light.
Why can’t you use LED bulbs with a dimmer switch?
Yes, LED bulbs can be used on a dimmer but they need to be listed as dimmable. LEDs can still work with incandescent dimmers, but the compatibility is an essential factor. Look at manufacturers’ website to figure out the right bulb and dimmer for your home. I’ve done all the research, so you won’t have to.
Why do my LED lights flicker on a dimmer switch?
put simply, LEDs flicker when their light output fluctuates. This fluctuation happens because your dimmable light-emitting diodes are designed to switch on and off at very high speed.
Which dimmer is best for LED lights?
Trailing edge dimmers work best with LED light bulbs and leading-edge dimmers work best with traditional incandescent and halogen light bulbs.
