How do I fix error 20 on my AEG dishwasher?

  1. Make sure that the sink spigot is not clogged.
  2. Make sure that the interior filter system is not clogged.
  3. Ensure that the drain hose has been installed correctly (see image below):
  4. Check whether the blanking plug has been removed from the sink drain. (

How do I reset the error code on my AEG dishwasher?

On a display like this to reset the appliance, press and hold the On/Off button on the appliance for 3 seconds. This will reset the appliance and clear any previously set programmes. On a display like this to reset the appliance, press and hold the On/Off button on the appliance for 3 seconds.

How do you clear a dishwasher error code?

Sometimes disconnecting power to the dishwasher for 30 seconds will clear the fault, error or function code.

How do I fix error 20 on my AEG dishwasher? – Related Questions

What are the most common faults with dishwasher?

Here are the five most common problems with dishwashers (and how to fix them).
  • #1 Problem: Dishes not drying.
  • #2 Problem: Dishwasher not draining.
  • #3 Problem: Dishwasher leaves spots or a film on glassware.
  • #4 Problem: Dishwasher running too long.
  • #5 Problem: Crumbs and food on dishes.

How do I know if my dishwasher inlet valve is clogged?

Signs pointing to a faulty inlet valve include: Leaks that fill the dishwasher when it’s off. Inadequate water for a cycle. The dishwasher fills too slowly or not all.

What should I do when my dishwasher shows the water tap error light?

How do I clear the error code on my Whirlpool dishwasher?

Press the “Heated Dry” button, followed by pressing the “Normal” button, and then press both buttons again in quick succession. Once you’ve pressed the two buttons twice, your dishwasher should go into a diagnostic mode, which will cause it to reset. If it doesn’t work, try doing it again with the door open.

How do I clear E4 error on dishwasher?

Error message E4 in free-standing compact dishwasher indicates too much inlet water and/or a leak.


  1. Make sure that the drain hose is correctly connected.
  2. Make sure that the filters in the appliance are clean.
  3. Make sure that the kitchen sink drains correctly.

How do I reset my LG dishwasher error code be?

This can usually be corrected by performing the following steps:
  1. Press the POWER button to turn the dishwasher off.
  2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds.
  3. Turn the circuit breaker to the dishwasher back ON.
  4. Press the POWER button to turn the dishwasher ON, and start a new cycle.

How do I force my LG dishwasher to drain?

Force the Drain.

This is activated by pressing and holding 2 buttons simultaneously e.g DELICATE + DUAL CONTROL. The 2 buttons may vary depending on your model. If your model does not have a CANCEL & DRAIN option, start a cycle, let it run for 45 seconds, then power the unit off.

What else can I do to solve the e25 error code on my dishwasher?

An e25 error code indicates that either the drain pump is blocked or the drain pump cover is loose. A blockage in the drain hose or a clogged filter may also cause the e25 error code. To fix the issue, the drain pump and dishwasher filter should be cleaned out and checked for damage.

How do I clear the error code on my LG washing machine?

To fix this:
  1. Press POWER, and turn the machine OFF.
  2. Unplug the machine.
  3. With the power being disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in.
  5. Power the unit back ON.
  6. Press-in on the door firmly.
  7. Select any cycle, and press START/PAUSE.

How do you force a washing machine to reset?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

What are the error codes for an LG dishwasher?

LG dishwasher error codes
  • IE. Not filling. Check/ Repair.
  • OE. Not draining. Check/ Repair.
  • AE or E1. Water leak detected. Check/ Repair.
  • FE. Water overflow detected. Check/ Repair.
  • tE. Thermistor (temperature sensor) failure. Check/
  • LE. Locked up circulation pump motor. Check/
  • HE. Heater failure. Check/
  • nE. Diverter motor failure. Check/

How do I reset my digital washer?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Does unplugging a washer reset it?

On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

Is a powerwash a factory reset?

A Powerwash factory reset erases all the information on your Chromebook’s hard drive, including your settings, apps, and files. The factory reset won’t delete any of your files on Google Drive or an external hard drive. Before performing the reset, back up your files on Google Drive or an external hard drive.

How do you reset a washer that won’t drain?

Perform a Master Reset

Unplug your washer for about one minute. Then, plug the appliance back in. Open and close the door six times in 12 seconds to tell the computer to reset everything. This may not work on all machines, but it’s an easy fix if yours is compatible with this technique.

Om forfatteren

Maiken Kaspersen lever og ånder for å gjøre hjemmet til et best mulig sted å leve, være med familien og nyte livet til det fulle.

Med mange års erfaring innen interiør, kjøkken og arkitektur, har Maiken mye kunnskap å dele med leserne av Drømmehjem.

Leave a Comment